# phoebey05/arduino-obstacle-course architecture

> Architecture diagram of the GitHub repository phoebey05/arduino-obstacle-course, generated by GitDiagram from its file tree, README and a sample of source files (last updated 2025-04-02). It is an AI-made overview: check details against the source.

- Interactive diagram: https://gitdiagram.com/phoebey05/arduino-obstacle-course
- Repository: https://github.com/phoebey05/arduino-obstacle-course

## Overview

This project is an Arduino-based obstacle course project geared toward beginners who want to experiment with input/output devices on an Arduino UNO. The core functionality centers on reading inputs (from a dual-axis joystick and potentiometer) and displaying information on a 16x2 LCD. Additionally, the Room.cpp and Room.h files suggest that some portion of the project’s logic—perhaps related to the “room” or level configuration in the obstacle course—is encapsulated in a dedicated module.

##### Main Components
- Hardware Components:
- Arduino UNO R3 (the central processing unit where your software runs)
- Dual-Axis XY Joystick (input component)
- 16x2 LCD Display (output component)
- Potentiometer (input or config control)
- 220ohm Resistor (circuit protection/current limiting)
- Wiring (Male to Female, Male to Male jumper wires for connections)
- Software Components:
- obstaclecourse.ino – this is the main Arduino sketch that handles initialization, the main loop, and overall control flow.
- Room.cpp and Room.h – a module likely responsible for managing the "room" or environmental aspects of the obstacle course. It could contain functions to set up challenges or represent a level.
- .gitignore and README.md are documentation and project management files.

##### Out Relationships and Interactions
- The Arduino UNO is at the center of the architecture.
- Joystick → Arduino (for user input)
- Potentiometer → Arduino (for input or configuration)
- Arduino → LCD Display (for visual output)
- Within the software layer:
- Optionally, include a small annotation indicating that the Room module abstracts part of the game logic or obstacle course configuration.

##### Architectural Patterns & Technologies
- Hardware Abstraction Layer: The code in obstaclecourse.ino that directly interacts with hardware (reading sensor values, sending commands to the LCD).
- Application Logic/Room Module: All obstacle course logic abstracted into Room.cpp/h.

a. Start by drawing the central Arduino UNO block.
b. Around it, place smaller blocks for each connected hardware device (Joystick, LCD, Potentiometer, etc.) with connecting lines showing their interfaces (digital/analog pins).
c. Inside or connected to the Arduino block, detail the main software elements:
- Obstaclecourse.ino acting as the main program.
- The Room module as a separate block connected to obstaclecourse.ino, representing a logical abstraction used in the application.
d. Typical data/control flows (e.g., “Joystick Input”, “LCD Output”, “Command to Room Module”).

## Diagram (Mermaid)

```mermaid
flowchart TD
    %% Hardware Components
    subgraph "Hardware Components"
        H1["Arduino UNO R3"]:::hardware
        H2["Dual-Axis XY Joystick"]:::hardware
        H3["Potentiometer"]:::hardware
        H4["16x2 LCD Display"]:::hardware
        H5["220ohm Resistor"]:::hardware
        H6["Wiring"]:::hardware
    end

    %% Software Components
    subgraph "Software Components"
        S1["obstaclecourse.ino (Main Sketch)"]:::software
        S2["Room Module (Room.cpp/h)"]:::software
        S3a["README.md"]:::software
        S3b[".gitignore"]:::software
    end

    %% Hardware interactions
    H2 -->|"JoystickInput"| H1
    H3 -->|"PotInput"| H1
    H1 -->|"LCDOutput"| H4
    H5 -->|"limits"| H4
    H6 -->|"connects"| H1

    %% Software interactions
    S1 -->|"uses"| S2

    %% Integration between Hardware and Software
    H1 -->|"runs"| S1

    %% Click Events
    click S1 "https://github.com/phoebey05/arduino-obstacle-course/blob/main/obstaclecourse.ino"
    click S2 "https://github.com/phoebey05/arduino-obstacle-course/blob/main/Room.cpp and Room.h"
    click S3a "https://github.com/phoebey05/arduino-obstacle-course/blob/main/README.md"
    click S3b "https://github.com/phoebey05/arduino-obstacle-course/blob/main/.gitignore"

    %% Styles
    classDef hardware fill:#ffcccc,stroke:#cc0000,stroke-width:2px;
    classDef software fill:#ccffcc,stroke:#008000,stroke-width:2px;
```
